00134012_0
Statischer Differenzdrucktransmitter VFP-300


00132079_0
Universalregler VRP


00134012_0
00132079_0

Static differential pressure transducers

For the static effective and differential pressure measurement

Differential pressure transducers based on the static measurement principle for volume flow rate measuring units Type VMR, VMRK or VME

  • Linear volume flow rate actual value 2 – 10 V DC
  • Recording of measured values for the display of volume flow rates or for the control of slave controllers
  • Parameters are factory set

Application

Application

  • Electronic volume flow controller Universal with static differential pressure transducer for use with volume flow rate measuring units
  • For applications with polluted extract air, e.g. with fluff, sticky particles or aggressive substances
  • Parameters are factory set
  • On-site adjusting is not required
  • For this application the Universal controller is only used for measuring the differential pressure and for transforming the measured value into a linear voltage signal. Connections for setpoint value signal and actuator are not relevant, and neither are the corresponding technical data.
  • Volume flow rate actual value is available as linear voltage signal

Description

Parts and characteristics

  • Sensor for static differential pressure measurements

Maintenance

  • Zero point correction once per year is recommended

Technical information

Function, Technical data, Produktbeziehungen

  • Function
  • Technical data
Principle of operation – static differential pressure transducer 00133112_0
① Differential pressure transducer
② Volume flow controller
③ Actual value signal


Functional description

The volume flow rate is determined by measuring the effective pressure. For this reason the measuring unit is fitted with an effective pressure sensor.

The static differential pressure transducer (diaphragm pressure transducer) transforms the effective pressure into a voltage signal. The volume flow rate actual value is hence available as a voltage signal. The factory setting is such that 10 V DC always corresponds to the nominal volume flow rate (Vnom).

Volume flow controller VRP

Supply voltage (AC)

24 V AC ± 20 %, 50/60 Hz

Power rating (AC)

without actuator max. 2.6 VA

Setpoint value signal input

2 – 10 V DC, Ra >100 kΩ

Actual value signal output

2 – 10 V DC linear, max. 0.5 mA

IEC protection class

III (protective extra-low voltage)

Protection level

IP 42

EC conformity

EMC according to 2014/30/EU


Static differential pressure transducer VFP-300

Supply voltage

from the controller

Measuring range

0 – 300 Pa

Linearity

± 3 Pa

IEC protection class

III (protective extra-low voltage)

Protection level

IP 42

EC conformity

EMC according to 2014/30/EU


Variants

  • Variants

Any attachments are to be defined with the order code of the volume flow rate measuring unit.

BB0

Application

  • Electronic volume flow controller VRP with static differential pressure transducer for use with volume flow rate measuring units
  • Separate casings for differential pressure transducer and controller electronics

Signal voltage range

  • 2 – 10 V DC

Parts and characteristics

  • Sensor for static differential pressure measurements

Installation and commissioning

  • Installation orientation is relevant
  • Zero point correction required

Static differential pressure transducers for volume flow rate measuring units

Order code detail Controller Static differential pressure transducer Volume flow rate measuring unit
Order code detail Part number Type Part number Type

BB0

M546EG2

VRP

M546EJ1

VFP-300

VMR, VME, VMRK


Electrical connection, Characteristics

  • Electrical connection
  • Characteristics
BB*, Klemmenbelegung 00132447_0
① Steckverbindung zum Anschluss des Differenzdrucktransmitters VFP
② Steckverbindung zum Anschluss des Stellantriebs
1 ⊥: Masse, Null
2 ~: Versorgungsspannung
3 w₁: Sollwertsignal
4 w₂: Sollwertsignal (0 – 20 V Phasenschnitt)
5 U5: Istwertsignal
6 y: Stellantriebssignal
7 z: Zwangssteuerung

Universal: VRP

Installation and commissioning

  • Installation orientation is relevant
  • Zero point correction required

Downloads

product information

production {"X-Frame-Options"=>"SAMEORIGIN", "X-XSS-Protection"=>"1; mode=block", "X-Content-Type-Options"=>"nosniff", "X-Download-Options"=>"noopen", "X-Permitted-Cross-Domain-Policies"=>"none", "Referrer-Policy"=>"strict-origin-when-cross-origin", "Strict-Transport-Security"=>"max-age=31536000; includeSubDomains", "Content-Type"=>"text/html; charset=utf-8"}

Share page

Recommend this page

Recommend this page by sending a link by mail.

Fields marked with an (*) are required fields.

Share page

Thank you for your recommendation!

Your recommendation has been sent and should arrive shortly.

Contact

We are here for you

Please specify your message and type of request.
Tel.: +32(0)2 522 07 80 | E-mail: info@trox.be

Attachment (max. 10MB)

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +32(0)2 522 07 80 | E-mail: info@trox.be

Contact

We are here for you

Please specify your message and type of request.
Tel.: +32(0)2 522 07 80 | E-mail: info@trox.be

Attachment (max. 10MB)

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +32(0)2 522 07 80 | E-mail: info@trox.be